I came across a way of building a garden fountain out of pots that I hadn't seen before. The idea of using pots as fountains is not new but I think this version makes a wonderful addition to any garden and its very easy to do. The first thing to do is choose the pots for your fountain. The three pots will be used for a basin, a base and the larger pot that will be used as the fountain. When choosing the shape of pot for the main fountain, keep in mind how it will function and not just how it looks. Slightly tapered pots that are smooth will be quieter since the water clings to the sides as it goes down. Other pots having rings or ridges will cause the falling water to produce more sound.
Start with the large terracotta (or stone) bowl as the basin for your garden pot fountain. This will be the foundation for your fountain where the overflowing water will fall into. Using a power drill and masonry bit, drill out a hole from the center of the bowl (if necessary). Now you can run the cord from the pump out through the hole. Cover this hole with duct tape and fill it in with a car body filler. When its dry, use silicon to fill in around the cord. You should now be ready to place the pot in your desired location. Try to place this as level as possible, but its not crucial for the fountain to run properly.
The pump is housed inside the base pot that is turned upside down. The diameter of the base should match the diameter of the main large fountain pot. Cut out three or four notches around the top rim of the pot. Its easier to do this if you soak the pot in water overnight. The purpose of the notches is to let water pass in to the base to the pump.
For the tubing, cut a piece of pipe about a foot longer than the height of the main fountain pot and attach to the pump. Now you must feed the pot used for the base down over the tube through the hole in the bottom. Apply silicon around the gap between the tube and the bottom of the pot. The whole set up at this point will be the basin with a pump inside an upside down pot sitting in the middle of it and the pipe sticking out the top of the base pot.
Now things should start taking shape. Take the fountain pot and test fit it down over the tube by placing it on top of the base pot. Don't glue it down yet. If it looks good (with the pipe sticking out past the top of the pot) you can take it back off and run a couple of thick beads of silicon around the top of the base pot. The bead around the outside diameter helps hold the two pots together and the bead on the inside closer to the hole will keep water from running in between the pots.
When it is all dry, test it by filling it with water. Adjust the height of the tubing to get the desired effect of the water bubbling up. Finish it off by filling the bottom basin pot with rocks. Enjoy your beautiful fountain!
Start with the large terracotta (or stone) bowl as the basin for your garden pot fountain. This will be the foundation for your fountain where the overflowing water will fall into. Using a power drill and masonry bit, drill out a hole from the center of the bowl (if necessary). Now you can run the cord from the pump out through the hole. Cover this hole with duct tape and fill it in with a car body filler. When its dry, use silicon to fill in around the cord. You should now be ready to place the pot in your desired location. Try to place this as level as possible, but its not crucial for the fountain to run properly.
The pump is housed inside the base pot that is turned upside down. The diameter of the base should match the diameter of the main large fountain pot. Cut out three or four notches around the top rim of the pot. Its easier to do this if you soak the pot in water overnight. The purpose of the notches is to let water pass in to the base to the pump.
For the tubing, cut a piece of pipe about a foot longer than the height of the main fountain pot and attach to the pump. Now you must feed the pot used for the base down over the tube through the hole in the bottom. Apply silicon around the gap between the tube and the bottom of the pot. The whole set up at this point will be the basin with a pump inside an upside down pot sitting in the middle of it and the pipe sticking out the top of the base pot.
Now things should start taking shape. Take the fountain pot and test fit it down over the tube by placing it on top of the base pot. Don't glue it down yet. If it looks good (with the pipe sticking out past the top of the pot) you can take it back off and run a couple of thick beads of silicon around the top of the base pot. The bead around the outside diameter helps hold the two pots together and the bead on the inside closer to the hole will keep water from running in between the pots.
When it is all dry, test it by filling it with water. Adjust the height of the tubing to get the desired effect of the water bubbling up. Finish it off by filling the bottom basin pot with rocks. Enjoy your beautiful fountain!
About the Author:
Donald Rickerby has been working in gardens since his early childhood and has always been interested in educating others on garden pot and landscaping techniques. If you'd like to know more about garden pots, visit AllGardenPots.com
No comments:
Post a Comment