In case you have been longing for that quiet fishing trip and you have an outboard powered by gas, then Torqeedo electric outboard is just the right solution for you. The cost of maintaining it is relatively less costly. Of importance to note is that it seldom requires any maintenance at all.
The gas powered outboards are usually very easy to operate due to the fact that they are able to provide a high mileage. Regardless of this fact, they pose grave danger to the environment as well as having a pretty higher maintenance cost. A much cheaper solution is to convert an old gas powered outboard to an electric one, rather than considering purchase of a new one.
A simple conversion to an electric one just requires changing the muffler. Alternatively, instead of purchasing a new one, you can convert an old gas-powered one to one that is electrically powered. In case you would like to perform the conversion on your outboard, you can follow the steps discussed below.
First, switch off the gasoline powered outboard. With the aid of a screwdriver, unscrew its casing. You will then be required to utilize a wrench to unbolt that gas tank and then raise it up.
The next step is to unbolt the motor and remove it from the engine. The bolts on the cylinders and piston are then taken out. Then, you need to position the outboard that is electric to replace the one that functions with gasoline.
After positioning it, the motor and the drive shaft should be matched up together and aligned. Ensure that the two tips are fixed together firmly in a perpendicular manner. The motor should then be able to turn when the drive shaft is turned.
You must then bolt the motor firmly in place. The control panel should then be unscrewed by unscrewing the wires from the socket and pulling them out. Pull out the wires and raise the control panel. You should then replace the control panel with a 300-amp, after which the wires should be connected back. Pull the battery sockets from the engine and then fix back the case.
You will now be required to drill a few holes at the rear of the boat on the engine bracket. Drill should tree in total; at one end of the leather strap and two more, one on each side of the rack. The strap end should then be fixed to the left side hole by bolting it.
Positioning the six batteries side by side, cover them with the strap and pull it tight. After this, a hole should be drilled in the strap and bolted in. Next, you should bolt the outboard onto the engine bracket.
Having bolted the outboard, you now need to connect the positive wire originating from the left cell to the negative part on the right side. Likewise, connect the negative area of the wire to the negative socket. The batteries should all be arranged in a sequence. Eventually, connect the positive socket from the controller to the positive(+) wire from the right side battery. Having finished all these steps, your Torqeedo electric outboard is now ready to take you down the river for fishing.
The gas powered outboards are usually very easy to operate due to the fact that they are able to provide a high mileage. Regardless of this fact, they pose grave danger to the environment as well as having a pretty higher maintenance cost. A much cheaper solution is to convert an old gas powered outboard to an electric one, rather than considering purchase of a new one.
A simple conversion to an electric one just requires changing the muffler. Alternatively, instead of purchasing a new one, you can convert an old gas-powered one to one that is electrically powered. In case you would like to perform the conversion on your outboard, you can follow the steps discussed below.
First, switch off the gasoline powered outboard. With the aid of a screwdriver, unscrew its casing. You will then be required to utilize a wrench to unbolt that gas tank and then raise it up.
The next step is to unbolt the motor and remove it from the engine. The bolts on the cylinders and piston are then taken out. Then, you need to position the outboard that is electric to replace the one that functions with gasoline.
After positioning it, the motor and the drive shaft should be matched up together and aligned. Ensure that the two tips are fixed together firmly in a perpendicular manner. The motor should then be able to turn when the drive shaft is turned.
You must then bolt the motor firmly in place. The control panel should then be unscrewed by unscrewing the wires from the socket and pulling them out. Pull out the wires and raise the control panel. You should then replace the control panel with a 300-amp, after which the wires should be connected back. Pull the battery sockets from the engine and then fix back the case.
You will now be required to drill a few holes at the rear of the boat on the engine bracket. Drill should tree in total; at one end of the leather strap and two more, one on each side of the rack. The strap end should then be fixed to the left side hole by bolting it.
Positioning the six batteries side by side, cover them with the strap and pull it tight. After this, a hole should be drilled in the strap and bolted in. Next, you should bolt the outboard onto the engine bracket.
Having bolted the outboard, you now need to connect the positive wire originating from the left cell to the negative part on the right side. Likewise, connect the negative area of the wire to the negative socket. The batteries should all be arranged in a sequence. Eventually, connect the positive socket from the controller to the positive(+) wire from the right side battery. Having finished all these steps, your Torqeedo electric outboard is now ready to take you down the river for fishing.
About the Author:
You can visit the website www.humberboats.ca for more helpful information about Switching From A Gasoline Powered To Torqeedo Electric Outboard
No comments:
Post a Comment