Driving a car with a cracked windscreen is dangerous and may lead to road accidents. For this reason, car owners in Jacksonville FL are advised to carry out a windshield replacement as soon as it breaks. It does not matter whether you had done a replacement before, installing new windscreens is a way for you to get back to road.
The replacement glass for an automobile can be purchased new or be obtained from a yard owned by a wrecker in Jacksonville FL. If you decide to buy it from the latter, make sure that you check for cracks and chips with your own eyes before handing over any cash. To prevent any damages that may occur during its transportation, you should cushion the detached windshield using a duvet.
You are then supposed to carefully remove the plastic surround side and the molding covering. You should cautiously go about this step so as not pry the clips that are holding them on. These clips are important because they are specific to the type of car. They help you save a lot of time but in case you cannot afford them, you will need to glue the moldings onto the car manually.
Next in your replacement procedure should be to cut the urethane from the outside between the glass and the pinch weld using a cold knife. This process takes between fifteen minutes to one hour depending on the experience and the tools that are using. The urethane is simply the flexible film that allows the windscreen to move without breaking when stress is applied to it during driving.
Before placing the replacement windscreen, prepare a pinch weld first. It involves brushing away visible dirt and then using plain water to wash away any remaining dirt. After doing so, use razor blade to cut the old urethane in the frame of the windscreen on the car to about 3mm. The rusty areas that remain exposed should be primed.
When making glass ready using the primer, make sure the primer you are using is specifically made to adhere to the specific urethane you will apply. The primer is meant to open up the molecules of the frit band. A frit band is the continuous black thread running around the edge of the glass. Here, glass is basically being prepared to accept the molecules of the urethane. After preparing the glass, attach the molding to it. After doing that, attach the urethane.
Using an electric caulking gun, apply the urethane to the glass. The electric gun ensure a consistent bead thereby avoiding leakages. It is good to know that the old urethane is the best thing that the new urethane will properly adhere to. This old urethane should be free from dirt, oil or other contaminants. You should ensure that the wind will not recontaminate the pinch weld before the adhesive urethane is applied.
You should then carefully place the windscreen to your car. If you are not using the mounting block, make sure that you wear a pair of latex gloves. They will ensure you do not touch the glass with your bare hands as doing this will contaminate the activated glass and will reduce the adhesiveness of the activator.
The replacement glass for an automobile can be purchased new or be obtained from a yard owned by a wrecker in Jacksonville FL. If you decide to buy it from the latter, make sure that you check for cracks and chips with your own eyes before handing over any cash. To prevent any damages that may occur during its transportation, you should cushion the detached windshield using a duvet.
You are then supposed to carefully remove the plastic surround side and the molding covering. You should cautiously go about this step so as not pry the clips that are holding them on. These clips are important because they are specific to the type of car. They help you save a lot of time but in case you cannot afford them, you will need to glue the moldings onto the car manually.
Next in your replacement procedure should be to cut the urethane from the outside between the glass and the pinch weld using a cold knife. This process takes between fifteen minutes to one hour depending on the experience and the tools that are using. The urethane is simply the flexible film that allows the windscreen to move without breaking when stress is applied to it during driving.
Before placing the replacement windscreen, prepare a pinch weld first. It involves brushing away visible dirt and then using plain water to wash away any remaining dirt. After doing so, use razor blade to cut the old urethane in the frame of the windscreen on the car to about 3mm. The rusty areas that remain exposed should be primed.
When making glass ready using the primer, make sure the primer you are using is specifically made to adhere to the specific urethane you will apply. The primer is meant to open up the molecules of the frit band. A frit band is the continuous black thread running around the edge of the glass. Here, glass is basically being prepared to accept the molecules of the urethane. After preparing the glass, attach the molding to it. After doing that, attach the urethane.
Using an electric caulking gun, apply the urethane to the glass. The electric gun ensure a consistent bead thereby avoiding leakages. It is good to know that the old urethane is the best thing that the new urethane will properly adhere to. This old urethane should be free from dirt, oil or other contaminants. You should ensure that the wind will not recontaminate the pinch weld before the adhesive urethane is applied.
You should then carefully place the windscreen to your car. If you are not using the mounting block, make sure that you wear a pair of latex gloves. They will ensure you do not touch the glass with your bare hands as doing this will contaminate the activated glass and will reduce the adhesiveness of the activator.
About the Author:
The following online page is one of the most reliable sources of information about auto windshield replacement. Come and review the published posts by logging on to http://www.ameriproautoglass.com immediately.
No comments:
Post a Comment