Installing a new stereo in your vehicles is a good way to breathe in new life from the old driving days. Adding an MP3 or CD player can give the opportunity to listen to news, music and also improves the overall quality of sound on the cars sound systems. Performing the installation all by yourself is not easy. It requires dedication and patience. Every model of a car is different as well as its stereos. When it comes with car stereo san antonio, individuals can do the installation without any assistance.
Buy an adaptor. The new device will have a diagram to be followed that will indicate where the proper connections has to be connected. However, this could be easily done when using a harness. The adaptors are quick to connect with the existing clips. By using the adaptor, it will eliminate the risk of making mistakes when doing the wiring.
Unscrew all the screws that are positioned at the trims. Be very careful when removing the screws to prevent the trim from getting damage. Use a tool when removing it and not just by hands. This will give you a steady grip on the screw and remove it much faster.
Install the output converter if required. Some cars will require the output converters to function properly especially if the components are rare. Inquire the aid of the store and ask how it must be installed. They know the right procedure and they can assist in doing the installations.
Pull out the necessary components. The components may be important but if the new installation will require to remove it, then do the process. Disconnect the components that are being wired directly into the car. Make sure that you will remember all their placements for returning them later. If possible, take a few pictures where they are located for easy access.
Connect the power sources. If the new stereos have harnesses for wiring, then the connection is already on once the wire is connected. If not, manually connect it to the power source. The car power has a color coded power source which is red or yellow. Some uses both the colors.
Pull out the equipment from its panel. Use a needle nose pliers to easily pull out the component. Simply give it a gentle pull. If the equipment does not budge or hard to pull, then there must be a few nuts that still in place. Double check the wiring and nuts once again.
Secure it. If the devices are using spring clips, then it will make a clicking sound when it is already locked in place. There will be no need to further secure it. If the equipment uses brackets and bolts, reused all the bolts that was being removed earlier and attached them in the same place before.
The process is difficult. However, if you learn the right procedure, then it can be done by yourself. There is no need for you to hire a professional to handle the process.
Buy an adaptor. The new device will have a diagram to be followed that will indicate where the proper connections has to be connected. However, this could be easily done when using a harness. The adaptors are quick to connect with the existing clips. By using the adaptor, it will eliminate the risk of making mistakes when doing the wiring.
Unscrew all the screws that are positioned at the trims. Be very careful when removing the screws to prevent the trim from getting damage. Use a tool when removing it and not just by hands. This will give you a steady grip on the screw and remove it much faster.
Install the output converter if required. Some cars will require the output converters to function properly especially if the components are rare. Inquire the aid of the store and ask how it must be installed. They know the right procedure and they can assist in doing the installations.
Pull out the necessary components. The components may be important but if the new installation will require to remove it, then do the process. Disconnect the components that are being wired directly into the car. Make sure that you will remember all their placements for returning them later. If possible, take a few pictures where they are located for easy access.
Connect the power sources. If the new stereos have harnesses for wiring, then the connection is already on once the wire is connected. If not, manually connect it to the power source. The car power has a color coded power source which is red or yellow. Some uses both the colors.
Pull out the equipment from its panel. Use a needle nose pliers to easily pull out the component. Simply give it a gentle pull. If the equipment does not budge or hard to pull, then there must be a few nuts that still in place. Double check the wiring and nuts once again.
Secure it. If the devices are using spring clips, then it will make a clicking sound when it is already locked in place. There will be no need to further secure it. If the equipment uses brackets and bolts, reused all the bolts that was being removed earlier and attached them in the same place before.
The process is difficult. However, if you learn the right procedure, then it can be done by yourself. There is no need for you to hire a professional to handle the process.
About the Author:
Get a summary of the factors to consider before selecting an installer of car stereo San Antonio systems and more information about a knowledgeable installer at http://www.baudiosound.com/car-audio-system now.